Видео

Hey sir. Nice video...salute. 对床机学生们您的视频很值得一切谢谢

geez this video is poorly done

Use a pair of tongs to remove the swarf from the lathe instead of hands. That stuff will reef your skin up bad.

If the thread gauge nut is large enough to fit over the center of the tail stock, place it on there before the work piece and it will be ready to check the threads without removing the part from the lathe

The year is 2024 and we as a country have failed ourselfs to keep the trades alive hope it changes

Make sure your tools are on Center

good stuff 👌

Wow, Dexter really made a career change at some point in his life.

So what happened? 10 videos posted then gone.......... ????

My GrandMaster always telling me it's taken life time practices and learning but you can not Reach Nirvana... when he's passed away he's was 95 years old.. I'm was in my mid 20 .. I'm now 50 years old I'm still practicing and learning..I have not reach Nirvana yet...

How to use an obsolete machine ? Maybe make a video of how to use a commodore computer?

Это станки шедевры и мечта миллионов сегодняшних мужчин с руками не из жопы

This guy doesn't use lubricant ??

That was fascinating ! I just got a big old industrial milling machine and am now looking how to use it. Didn't realize it was an hour long though...2:16 am, oops!

One of the best videos I’ve seen on RUclips about the lathe and it’s working for the older machines. It is a very cool piece. Thanks for sharing it with us.

Thank you so much!!😊

just got here and yes I am necro'ing the feed but ty for the vid

It seems that part of the skills then was not to get injured when working. This reminds me of a mechanical engineer who always wear white coveralls when working or inspecting work in the engine room of ships under repair in a dock yard and never once saw his clothes soiled

You are excellent instructo to clear teching about mAchine shop.

Went to a vocational high school for Machine Tool. Hated every minute of it. Now, looking back over thirty years, I'm amazed how much I remember. I can smell this video. Especially when the cut starts.

Tak niewolnicy zwani robotnikami zapierdalają u kapitalisty na kromkę chleba ten żydowski film zakłamuje i nie pokazuje PRAWDZIWEGO obrazu w jakich poniżających godności człowieka warunkach każe się robotnikom na świecie zapierdalać

Thank you! Great info! Greatings from the netherlands.

The "jumping" of the drill comes from the taper, wich is NOT "working as a funnel". A drill must be centered by his tip. That taper from the centerdrill just makes him scratching with one cutting edge, so it dances arround. Better to make just a small and short start hole with the center drill.

Make sure at all times your camera is in focus. As it is imposable to see the information you are trying to impart, and blurred shots drive one to distraction. You need to get the basics right!

It is downloading and you have to understand that is the best compliment!

LarryBoy And The Angry Eyebrows March 2002

2002 Calendar

Number 2

March 2002

I have a South bend . Love it.

had to replay that first bit before i got it... "special steel", NOT "stainless steel"... was worried that they messed up in teh first few seconds. that would have been a concern...

Don’t consider trying to fix something that is broken! Good job,Monte! 0:02

Good job Monte’

Nothing beats Old School! Nothing!

The book was better than the movie... 🤣😂🤣

I had apprentices in my machine shop. I always made sure safety was of paramount importance where i never allowed anyone using a file. Files have contributed to many serious injuries to artisans. The use of a file on a lathe is not allowed by the apprentice board and workman's inspectors in our county.

What a wonderfully quiet lathe!

Thank you for video.

It is interesting how were made first machine tools in times when there were no machine tools

hey guys wondering if anyone in the New York area would willing to teach me the basic operation of the lathe and Bridgeport machines willing to compensate for your time. Thank you.

The best video for metal turning LEVEL 1 UK. This will make you pass if you follow this. (without the file for breaking the edge) Excellent video

Why am I watching this😂

Loved that class in jr high school

Все думают что станочники full idiots. I'm станочник.

Is this guy 7 foot tall or something? I have to use a step stool to reach my draw bar. And I don't have a riser in my mill ? 🤣

Thanks much

Excellent Video and excellent precise instructor.

this is just awesome , why isn't anybody making movies like this anymore , people used to really cared about making educational content

You can leave the half nut lever engaged

I like the knowledge l.but the resolution is brutal